ERSATZTEIL-FINDER

Yokomo

Ordnen nach:
Empfohlen
24
Front stabiliser wire (F1.2 mm) BD11
YOK-B11-412F2A
entspricht: B11-412F2
CHF8.90
Auf Lager  
+ −
Front stabiliser wire (F1.3 mm) BD11
YOK-B11-412F3A
entspricht: B11-412F3
CHF8.90
Auf Lager  
+ −
Aluminium stabiliser mount (A) BD11
YOK-B11-412MAA
entspricht: B11-412MA
CHF11.90
Auf Lager  
+ −
Aluminium stabiliser mount (B) BD11
YOK-B11-412MBA
entspricht: B11-412MB
CHF11.90
Auf Lager  
+ −
Stabiliser wire (F1.1 mm) BD11
YOK-B11-412R1A
entspricht: B11-412R1
CHF8.90
Auf Lager  
+ −
Stabiliser wire (F1.2 mm) BD11
YOK-B11-412R2A
entspricht: B11-412R2
CHF8.90
Auf Lager  
+ −
Stabiliser wire (F1.3 mm) BD11
YOK-B11-412R3A
entspricht: B11-412R3
CHF8.90
Auf Lager  
+ −
F5mm suspension ball (4 pieces) BD11
YOK-B11-B50A
entspricht: B11-B50
CHF8.90
Auf Lager  
+ −
RTC steering block arm plate BD11
YOK-B11-RTC-5A
entspricht: B11-RTC-5
CHF11.90
Auf Lager  
+ −
Shock shaft guide (4 pieces) BD11
YOK-B11-S2BA
entspricht: B11-S2B
CHF11.90
Auf Lager  
+ −
Shock adjust nut / O-ring (2 pieces) BD11
YOK-B11-S4CA
entspricht: B11-S4C
CHF12.90
Auf Lager  
+ −
Optional parts set for BD11 Upgrade 2
YOK-B11-OP2A
entspricht: B11-OP2
CHF32.90
Auf Lager  
+ −
Silver solder (15g with silver)
YOK-YT-SS2A
Yokomo's Silver Solder (solder line) has been renewed! It is a high quality 0.8mm solder wire with resin and has an internal capacity of 15g. Silver-coated silicon cords are often used for radio-controlled car wiring, but if normal solder is used, the silver component will dissolve into the...
CHF8.90
Auf Lager  
+ −
BD11 decal sheet
YOK-ZC-BD11-1A
A decal sheet with the BD11 and Yokomo logos. It's perfect for dressing up your machine, and sticking it on your body will increase your attachment to the machine.
CHF8.90
Auf Lager  
+ −
Graphite molded Front sus-arm for YZ-4SF2
YOK-S4-008F2GA
entspricht: S4-008F2G
CHF15.90
Auf Lager  
+ −
Stabiliser Wire BD11 front 1.4mm
YOK-B11-412F4A
F1.4mm is added as a variation of the sway bar wire for BD11. This wire is one rank stiffer than the previous lineup and is mainly used to limit roll on high-grip surfaces. Compared to BD10, BD11 has a lower lever ratio and is more compatible with softer springs. However, on...
CHF9.90
Auf Lager  
+ −
Stabiliser wire BD11 hinten 1.4mm
YOK-B11-412R4A
CHF9.90
Auf Lager  
+ −
Rear short "X30" shock body for YZ-2DTM3 / CAL3
YOK-S4-S4MA
A shock body that can be used on the rear of the YZ-2DTM3 / CAL3 and the front of the YZ-2T. 1 bottle included.
CHF14.50
Auf Lager  
+ −
Body Mount Patch 6x0.5mm
YOK-ZR-BMP6B
entspricht: ZR-BMP6A
CHF7.50
Auf Lager  
+ −
Programmierbox für RPX3 ESC
YOK-BL-R26P3
A dedicated programmer is required to change the RPX3 program. We plan to distribute firmware to update the old programmer (BL-R26P), but you will need to revert to the old firmware (to be distributed) to change the program of the old ESC after the update.
CHF38.90
Auf Lager  
+ −
Receiver Capacitor (non-polarized)
YOK-BL-RRCP
This capacitor is connected to the BEC channel of the receiver to reduce noise and stabilize the servo current. When a large load is placed on the servo during driving, the capacitor can momentarily supplement power to stabilize the servo's operation. Since it is non-polarized, it...
CHF17.90
Auf Lager  
+ −
Big Bore Stossdämpfer Diaphragms 4stk. silicon
YOK-YS-8DS
CHF4.90
Auf Lager  
+ −
High Grade O-Ring (oil resistant blue, 8stk.)
YOK-YS-7HG2
CHF8.90
Auf Lager  
+ −
Progressive Federn 1.80 bis 2.10 20mm
YOK-B10-SSP18
This new spring matches the BD11 with a lower lever ratio than before. The overall setting is softer, making it a perfect match for the BD11's long suspension arms. You can find a good balance by choosing from this lineup for both front and rear. The progressive type spring has a pitch change...
CHF12.90
Auf Lager  
+ −
Verfügbarkeit
Verfügbar beim Lieferanten
Abmessungen
Auswahlhilfe
Material
Preis

CHF  –  CHF

  • ‎CHF1.5
  • ‎CHF949
Reifen/Rad-Typ
Servo-Typ
Verwendung
Massstab
Motor / Antrieb
Einsatz
Anspruch
Lackierung
Fertigungsgrad
Max. Geschwindigkeit
Marke
Betriebsspannung
Zurücksetzen (reset)