ERSATZTEIL-FINDER

Yokomo

Ordnen nach:
Empfohlen
24
Progressive Federn BD11 1.90-2.20 20mm
YOK-B10-SSP19
This new spring matches the BD11 with a lower lever ratio than before. The overall setting is softer, making it a perfect match for the BD11's long suspension arms. You can find a good balance by choosing from this lineup for both front and rear. The progressive type spring has a pitch change...
CHF12.90
Auf Lager  
+ −
Progressive Federn BD11 2.10 bis 2.40 20mm
YOK-B10-SSP21
CHF12.90
Auf Lager  
+ −
Yokomo Factory Jacke XL
YOK-ZC-J27XLA
A windproof jacket with the Yokomo Racing Factory logo on the chest and back. Light nylon fabric, perfect for changing seasons. It has a slightly larger size.
CHF37.90
Auf Lager  
+ −
Yokomo Factory Jacke L
YOK-ZC-J27LA
entspricht: ZC-J27L
CHF37.90
Auf Lager  
+ −
Rear hub carrier link mount für S4-415RS
YOK-S4-415RLA
entspricht: S4-415RL
CHF14.90
Auf Lager  
+ −
Rear short shock shaft for YZ-2DTM3/CAL3
YOK-S4-S2MA
entspricht: S4-S2M
CHF9.50
Auf Lager  
+ −
Inline Battery holder conversion für MD1.0
YOK-MD-CONV
This is a battery holder conversion to change the battery mounting of MD1.0 to inline mounting. When the car has a certain degree of grip, mounting the battery inline (in the front-back direction of the chassis) suppresses chassis roll, enabling sharper movement when transitioning to an...
CHF43.90
Auf Lager  
+ −
4 gear transmission conversion MD1.0
YOK-MD-CON4
The standard MD1.0 transmission has 3 gears and positive torque, but by adding a counter gear and reconfiguring it, this conversion set can be used with 4 gears and anti-torque specifications. Compared to a 3-gear transmission, the additional gear increases drive loss, but the...
CHF37.90
Auf Lager  
+ −
YZ-2CAL3.1/DTM3.1 Side plate (graphite molding)
YOK-Z2-002SG
Side plate for YZ-2CAL3.1/DTM3.1. Graphite-mixed resin is used to increase rigidity and improve steering response, especially on high-grip surfaces. In particular, pitching rigidity is increased, enabling the driver to gain a sense of stability from corner entry to clipping
CHF14.90
Auf Lager  
+ −
Rear Upper Mount/Roll Bar Holder/Gear Box
YOK-Z2-300RG
This is a set of resin parts around the rear for YZ-2CAL3.1/DTM3.1/Rear Upper Mount, Roll Bar Holder, and Gear Box Support. Graphite-mixed resin is used to increase rigidity, which is effective in gaining rear stability when turning and improving traction when accelerating.
CHF14.50
Auf Lager  
+ −
Side plate/battery post/antenna mount for YZ-4SF2
YOK-S4-002SPG
These graphite-mixed resin molded side plates can increase the rigidity of the YZ-4SF2 chassis. It is especially effective when driving on high grip surfaces, and improves stability when entering a corner, enabling cornering with good steering response. It is effective not only on...
CHF19.50
Auf Lager  
+ −
Rear Belt Tensioner BD11
YOK-B11-RBTS
Rear belt tensioner set for BD11. It is an effective part especially when a high-power motor is installed, and it is possible to suppress tooth jumping of the rear belt, improve drive efficiency, and make the belt itself last longer. European team drivers who participate in the ETS always wear...
CHF16.90
Auf Lager  
+ −
USB Program adaptor SP-02D/03D servo
YOK-SP-USBP
This is a program adapter to easily rewrite the performance of programmable servos for drifting such as SP-02D/03D, etc. Save the application on your PC, start it up, and connect it to the PC's Plug the adapter into the PC's USB connector and connect the servo connector. Power, torque,...
CHF33.90
Auf Lager  
+ −
Aluminum turnbuckle set for MD1.0
YOK-MD-TBS
This set converts the turnbuckles used in the MD series upper arms and tie rods to aluminum. 20mm/27mm/33mm turnbuckles are included, to reduce weight and improve suspension response.
CHF21.50
Auf Lager  
+ −
YOKOMO Parts Case 86X103X34mm
YOK-YC-13
new lineup of parts cases with the Yokomo logo has been added to the series. The three new cases are suitable for storing relatively small parts, and feature a large number of movable dividers that can be positioned in a variety of ways. The body is made of polypropylene, which is...
CHF8.90
Auf Lager  
+ −
YOKOMO Parts Case 205X145X40mm
YOK-YC-14
A new lineup of parts cases with the Yokomo logo has been added to the series. The three new cases are suitable for storing relatively small parts, and feature a large number of movable dividers that can be positioned in a variety of ways. The body is made of polypropylene, which is...
CHF13.90
Auf Lager  
+ −
BD-919/BD10/BD10LC AXON super hub axle pin/"O" rin
YOK-B10-WHAS2A
entspricht: B10-WHAS2
CHF4.50
Auf Lager  
+ −
Graphite front body mount stay for MD1.0
YOK-MD-016MG
CHF34.90
Auf Lager  
+ −
Alu hight mount battery post (F)
YOK-Y2-118FL
CHF16.90
Auf Lager  
+ −
Drift LTS Front Spring 0.9x45x8.5turns
YOK-D-186
CHF11.50
Auf Lager  
+ −
Drift LTS Front Spring 1.0×48mm×9.0turns
YOK-D-187
CHF11.90
Auf Lager  
+ −
Drift LTS Rear Spring 1.0×48mm×10.0turns
YOK-D-188
CHF11.90
Auf Lager  
+ −
F/R body mount for BD9/10/11 (hard)
YOK-B11-016H
CHF9.90
Auf Lager  
+ −
Titanium Lower Shock Mount for BD11
YOK-B11-S9T
CHF12.90
Auf Lager  
+ −
Verfügbarkeit
Verfügbar beim Lieferanten
Abmessungen
Auswahlhilfe
Material
Preis

CHF  –  CHF

  • ‎CHF1.5
  • ‎CHF949
Reifen/Rad-Typ
Servo-Typ
Verwendung
Massstab
Motor / Antrieb
Einsatz
Anspruch
Lackierung
Fertigungsgrad
Max. Geschwindigkeit
Marke
Betriebsspannung
Zurücksetzen (reset)