Français (CH)
ERSATZTEIL-FINDER

Yokomo

Trier par:
Recommandé
Montrer:
24
Progressive Federn BD11 2.10 bis 2.40 20mm
YOK-B10-SSP21
CHF 12.90
En stock  
+ −
Yokomo Factory Jacke XL
YOK-ZC-J27XLA
A windproof jacket with the Yokomo Racing Factory logo on the chest and back. Light nylon fabric, perfect for changing seasons. It has a slightly larger size.
CHF 37.90
En stock  
+ −
Yokomo Factory Jacke L
YOK-ZC-J27LA
entspricht: ZC-J27L
CHF 37.90
En stock  
+ −
Rear hub carrier link mount für S4-415RS
YOK-S4-415RLA
entspricht: S4-415RL
CHF 14.90
En stock  
+ −
High traction rear hub carrier weight
YOK-Y2-415RWA
A steel weight that can be attached directly to the rear hub carrier of the YD-2 series to increase rear traction. It is possible to effectively increase the rear grip by increasing the unsprung weight that directly applies the load to the tire without passing through a damper. The weight is...
CHF 32.90
En stock  
+ −
Rear short shock shaft for YZ-2DTM3/CAL3
YOK-S4-S2MA
entspricht: S4-S2M
CHF 9.50
En stock  
+ −
Inline Battery holder conversion für MD1.0
YOK-MD-CONV
This is a battery holder conversion to change the battery mounting of MD1.0 to inline mounting. When the car has a certain degree of grip, mounting the battery inline (in the front-back direction of the chassis) suppresses chassis roll, enabling sharper movement when transitioning to an...
CHF 43.90
En stock  
+ −
4 gear transmission conversion MD1.0
YOK-MD-CON4
The standard MD1.0 transmission has 3 gears and positive torque, but by adding a counter gear and reconfiguring it, this conversion set can be used with 4 gears and anti-torque specifications. Compared to a 3-gear transmission, the additional gear increases drive loss, but the...
CHF 37.90
En stock  
+ −
YZ-2CAL3.1/DTM3.1 Side plate (graphite molding)
YOK-Z2-002SG
Side plate for YZ-2CAL3.1/DTM3.1. Graphite-mixed resin is used to increase rigidity and improve steering response, especially on high-grip surfaces. In particular, pitching rigidity is increased, enabling the driver to gain a sense of stability from corner entry to clipping
CHF 14.90
En stock  
+ −
Rear Upper Mount/Roll Bar Holder/Gear Box
YOK-Z2-300RG
This is a set of resin parts around the rear for YZ-2CAL3.1/DTM3.1/Rear Upper Mount, Roll Bar Holder, and Gear Box Support. Graphite-mixed resin is used to increase rigidity, which is effective in gaining rear stability when turning and improving traction when accelerating.
CHF 14.50
En stock  
+ −
Rear Belt Tensioner BD11
YOK-B11-RBTS
Rear belt tensioner set for BD11. It is an effective part especially when a high-power motor is installed, and it is possible to suppress tooth jumping of the rear belt, improve drive efficiency, and make the belt itself last longer. European team drivers who participate in the ETS always wear...
CHF 16.90
En stock  
+ −
Aluminum turnbuckle set for MD1.0
YOK-MD-TBS
This set converts the turnbuckles used in the MD series upper arms and tie rods to aluminum. 20mm/27mm/33mm turnbuckles are included, to reduce weight and improve suspension response.
CHF 21.50
En stock  
+ −
YOKOMO Parts Case 86X103X34mm
YOK-YC-13
new lineup of parts cases with the Yokomo logo has been added to the series. The three new cases are suitable for storing relatively small parts, and feature a large number of movable dividers that can be positioned in a variety of ways. The body is made of polypropylene, which is...
CHF 8.90
En stock  
+ −
YOKOMO Parts Case 205X145X40mm
YOK-YC-14
A new lineup of parts cases with the Yokomo logo has been added to the series. The three new cases are suitable for storing relatively small parts, and feature a large number of movable dividers that can be positioned in a variety of ways. The body is made of polypropylene, which is...
CHF 13.90
En stock  
+ −
BD-919/BD10/BD10LC AXON super hub axle pin/"O" rin
YOK-B10-WHAS2A
entspricht: B10-WHAS2
CHF 4.50
En stock  
+ −
Graphite front body mount stay for MD1.0
YOK-MD-016MG
CHF 34.90
En stock  
+ −
Alu high mount Battery Post (R)
YOK-Y2-118RL
CHF 23.90
En stock  
+ −
Alu hight mount battery post (F)
YOK-Y2-118FL
CHF 16.90
En stock  
+ −
Drift LTS Front Spring 0.9x45x8.5turns
YOK-D-186
CHF 11.50
En stock  
+ −
Drift LTS Front Spring 1.0×48mm×9.0turns
YOK-D-187
CHF 11.90
En stock  
+ −
Drift LTS Rear Spring 1.0×48mm×10.0turns
YOK-D-188
CHF 11.90
En stock  
+ −
F/R body mount for BD9/10/11 (hard)
YOK-B11-016H
CHF 9.90
En stock  
+ −
Titanium Lower Shock Mount for BD11
YOK-B11-S9T
CHF 12.90
En stock  
+ −
Graphite center stiffener for BD12
YOK-B12-302CS
CHF 19.90
En stock  
+ −
Verfügbarkeit
Verfügbar beim Lieferanten
Abmessungen
Auswahlhilfe
Material
Prix
CHF
–
CHF
  • CHF 1.5
  • CHF 949
Reifen/Rad-Typ
Servo-Typ
Verwendung
Massstab
Motor / Antrieb
Einsatz
Anspruch
Lackierung
Fertigungsgrad
Max. Geschwindigkeit
Marke
Betriebsspannung
Effacer