ERSATZTEIL-FINDER

Yokomo

Ordnen nach:
Empfohlen
24
Graphite center stiffener for BD12
YOK-B12-302CS
CHF19.90
Auf Lager  
+ −
Shock shaft guide for BD12
YOK-B12-S2B
CHF13.50
Auf Lager  
+ −
Aluminum spring cup for BD12 (bearing specificatio
YOK-B12-S3S
CHF10.50
Auf Lager  
+ −
Aluminum shock adjust nut/O ring for BD12
YOK-B12-S4AJ
CHF10.50
Auf Lager  
+ −
Aluminum upper shock cap nut for BD12
YOK-B12-S4C1
CHF9.70
Auf Lager  
+ −
Aluminum shock cylinder for BD12
YOK-B12-S4S
CHF24.90
Auf Lager  
+ −
Shock shaft for BD12
YOK-B12-S5S
CHF7.50
Auf Lager  
+ −
Shock cap/shock end for BD12
YOK-B12-S6
CHF7.50
Auf Lager  
+ −
AXON TCS 90T spur gear (hard)
YOK-SG-A6490
CHF7.50
Auf Lager  
+ −
Graphite rear upper deck 1.5mm für BD12
YOK-B12-003RS
CHF23.90
Auf Lager  
+ −
Graphite rear stiffener plate für BD11/BD12
YOK-B12-003RSP
CHF21.00
Auf Lager  
+ −
Belt tension adjustment cam for BD10/9 (2 pieces m
YOK-B10-BTCBA
entspricht: B10-BTCB
CHF19.90
Auf Lager  
+ −
Chassis Schutzfolie 200x390mm
YOK-ZC-CPS
Protective sheet that is attached to the back of the chassis to protect the chassis from road surface interference.The slightly thicker material and stronger adhesive surface ensure a firm bond. The price is reasonable for periodic replacement. It can be used for speed category,...
CHF3.90
Nicht auf Lager
Front Stabi Draht 0.9mm BD11/BD12
YOK-B11-412F09A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF8.90
Auf Lager  
+ −
Front Stabidraht 1.0mm BD11/BD12
YOK-B11-412F0A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF8.90
Auf Lager  
+ −
Stabidraht hinten 0.9mm BD11/BD12
YOK-B11-412R09A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF8.90
Auf Lager  
+ −
Stabidraht hinten 1mm BD11/BD12
YOK-B11-412R0A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF8.90
Auf Lager  
+ −
Aluminum motor mount for BD10F
YOK-B10-302MFA
Aluminum motor mount for BD10F. Backlash can be adjusted by sliding the joint with the center mount.
CHF22.90
Auf Lager  
+ −
Steel S2 Chassis weight (26g) for SO2.0
YOK-Z2-002WS
CHF15.90
Auf Lager  
+ −
Alum Adjustable Front Axle for SO2.0
YOK-Z2-010AFA
CHF16.90
Auf Lager  
+ −
Off-road body for SO series (light weight)
YOK-Z2-101S2L
CHF26.90
Auf Lager  
+ −
Wide front wing for SO series
YOK-Z2-107FW2
CHF8.90
Auf Lager  
+ −
Graphite Steering Block Plate DOT1for SO2.0
YOK-Z2-415S21
CHF11.50
Auf Lager  
+ −
Steering Block L/R (Hard) for SO2.0
YOK-Z2-415S2H
CHF6.90
Auf Lager  
+ −
Verfügbarkeit
Verfügbar beim Lieferanten
Abmessungen
Auswahlhilfe
Material
Preis

CHF  –  CHF

  • ‎CHF1.5
  • ‎CHF949
Reifen/Rad-Typ
Servo-Typ
Verwendung
Massstab
Motor / Antrieb
Einsatz
Anspruch
Lackierung
Fertigungsgrad
Max. Geschwindigkeit
Marke
Betriebsspannung
Zurücksetzen (reset)