Français (CH)
ERSATZTEIL-FINDER

Yokomo

Trier par:
Recommandé
Montrer:
96
4 gear transmission conversion MD1.0
YOK-MD-CON4
The standard MD1.0 transmission has 3 gears and positive torque, but by adding a counter gear and reconfiguring it, this conversion set can be used with 4 gears and anti-torque specifications. Compared to a 3-gear transmission, the additional gear increases drive loss, but the...
CHF 37.90
En stock
+ −
YZ-2CAL3.1/DTM3.1 Side plate (graphite molding)
YOK-Z2-002SG
Side plate for YZ-2CAL3.1/DTM3.1. Graphite-mixed resin is used to increase rigidity and improve steering response, especially on high-grip surfaces. In particular, pitching rigidity is increased, enabling the driver to gain a sense of stability from corner entry to clipping
CHF 14.90
En stock
+ −
Rear Upper Mount/Roll Bar Holder/Gear Box
YOK-Z2-300RG
This is a set of resin parts around the rear for YZ-2CAL3.1/DTM3.1/Rear Upper Mount, Roll Bar Holder, and Gear Box Support. Graphite-mixed resin is used to increase rigidity, which is effective in gaining rear stability when turning and improving traction when accelerating.
CHF 14.50
En stock
+ −
Side plate/battery post/antenna mount for YZ-4SF2
YOK-S4-002SPG
These graphite-mixed resin molded side plates can increase the rigidity of the YZ-4SF2 chassis. It is especially effective when driving on high grip surfaces, and improves stability when entering a corner, enabling cornering with good steering response. It is effective not only on...
CHF 19.50
En stock
+ −
Rear Belt Tensioner BD11
YOK-B11-RBTS
Rear belt tensioner set for BD11. It is an effective part especially when a high-power motor is installed, and it is possible to suppress tooth jumping of the rear belt, improve drive efficiency, and make the belt itself last longer. European team drivers who participate in the ETS always wear...
CHF 16.90
En stock
+ −
Aluminum turnbuckle set for MD1.0
YOK-MD-TBS
This set converts the turnbuckles used in the MD series upper arms and tie rods to aluminum. 20mm/27mm/33mm turnbuckles are included, to reduce weight and improve suspension response.
CHF 21.50
En stock
+ −
YOKOMO Parts Case 86X103X34mm
YOK-YC-13
new lineup of parts cases with the Yokomo logo has been added to the series. The three new cases are suitable for storing relatively small parts, and feature a large number of movable dividers that can be positioned in a variety of ways. The body is made of polypropylene, which is...
CHF 8.90
En stock
+ −
YOKOMO Parts Case 205X145X40mm
YOK-YC-14
A new lineup of parts cases with the Yokomo logo has been added to the series. The three new cases are suitable for storing relatively small parts, and feature a large number of movable dividers that can be positioned in a variety of ways. The body is made of polypropylene, which is...
CHF 13.90
En stock
+ −
BD-919/BD10/BD10LC AXON super hub axle pin/"O" rin
YOK-B10-WHAS2A
entspricht: B10-WHAS2
CHF 4.50
En stock
+ −
Graphite front body mount stay for MD1.0
YOK-MD-016MG
CHF 34.90
En stock
+ −
Alu high mount Battery Post (R)
YOK-Y2-118RL
CHF 23.90
En stock
+ −
Alu hight mount battery post (F)
YOK-Y2-118FL
CHF 16.90
En stock
+ −
Drift LTS Front Spring 0.9x45x8.5turns
YOK-D-186
CHF 11.50
En stock
+ −
Drift LTS Front Spring 1.0×48mm×9.0turns
YOK-D-187
CHF 11.90
En stock
+ −
Drift LTS Rear Spring 1.0×48mm×10.0turns
YOK-D-188
CHF 11.90
En stock
+ −
F/R body mount for BD9/10/11 (hard)
YOK-B11-016H
CHF 9.90
En stock
+ −
Titanium Lower Shock Mount for BD11
YOK-B11-S9T
CHF 12.90
En stock
+ −
Graphite center stiffener for BD12
YOK-B12-302CS
CHF 19.90
En stock
+ −
Brass center stiffener for BD12
YOK-B12-302CSB
CHF 35.90
En stock
+ −
Shock shaft guide for BD12
YOK-B12-S2B
CHF 13.50
En stock
+ −
Aluminum spring cup for BD12 (bearing specificatio
YOK-B12-S3S
CHF 10.50
En stock
+ −
Aluminum shock adjust nut/O ring for BD12
YOK-B12-S4AJ
CHF 10.50
En stock
+ −
Aluminum upper shock cap nut for BD12
YOK-B12-S4C1
CHF 9.70
En stock
+ −
Aluminum shock cylinder for BD12
YOK-B12-S4S
CHF 24.90
En stock
+ −
Shock shaft for BD12
YOK-B12-S5S
CHF 7.50
En stock
+ −
Shock cap/shock end for BD12
YOK-B12-S6
CHF 7.50
En stock
+ −
AXON TCS 90T spur gear (hard)
YOK-SG-A6490
CHF 7.50
En stock
+ −
Graphite rear upper deck 1.5mm für BD12
YOK-B12-003RS
CHF 23.90
En stock
+ −
Graphite rear stiffener plate für BD11/BD12
YOK-B12-003RSP
CHF 21.00
En stock
+ −
Belt tension adjustment cam for BD10/9 (2 pieces m
YOK-B10-BTCBA
entspricht: B10-BTCB
CHF 19.90
En stock
+ −
Chassis Schutzfolie 200x390mm
YOK-ZC-CPS
Protective sheet that is attached to the back of the chassis to protect the chassis from road surface interference.The slightly thicker material and stronger adhesive surface ensure a firm bond. The price is reasonable for periodic replacement. It can be used for speed category,...
CHF 3.90
En stock
+ −
Front Stabi Draht 0.9mm BD11/BD12
YOK-B11-412F09A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF 8.90
En stock
+ −
Front Stabidraht 1.0mm BD11/BD12
YOK-B11-412F0A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF 8.90
En stock
+ −
Stabidraht hinten 0.9mm BD11/BD12
YOK-B11-412R09A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF 8.90
En stock
+ −
Stabidraht hinten 1mm BD11/BD12
YOK-B11-412R0A
Sway bar for BD12/11 series touring car chassis. With 0.9mm and 1.0mm wire diameter settings, which are thinner than the previous lineup, these bars are mainly effective when driving on outdoor asphalt, using roll to increase grip. Please use as setting parts.
CHF 8.90
En stock
+ −
Aluminum motor mount for BD10F
YOK-B10-302MFA
Aluminum motor mount for BD10F. Backlash can be adjusted by sliding the joint with the center mount.
CHF 22.90
En stock
+ −
Aluminum clamp type servo horn for YD-2ZX
YOK-Y2-204Z26A
Aluminum servo horn for YD-2ZX. It has a shape that matches the mounting method where the servo is placed directly on the main chassis, and is a type that is fixed with a clamp through an adapter that matches the servos of each company.
CHF 21.00
En stock
+ −
Alum. S2 Chassis weight (9g) for SO2.0
YOK-Z2-002WA
CHF 16.90
En stock
+ −
Steel S2 Chassis weight (26g) for SO2.0
YOK-Z2-002WS
CHF 15.90
En stock
+ −
Alum Adjustable Front Axle for SO2.0
YOK-Z2-010AFA
CHF 16.90
En stock
+ −
Wide front wing for SO series
YOK-Z2-107FW2
CHF 8.90
En stock
+ −
Graphite Steering Block Plate DOT1for SO2.0
YOK-Z2-415S21
CHF 11.50
En stock
+ −
Steering Block L/R (Hard) for SO2.0
YOK-Z2-415S2H
CHF 6.90
En stock
+ −
Steering Block L/R (Graph) for SO2.0(2pcs.)
YOK-Z2-415S2G
CHF 11.90
En stock
+ −
M2 x 3mm flat head socket screw (4 pieces)
YOK-ZC-F23
CHF 2.90
En stock
+ −
Gokuraku off-road wing (straight)
YOK-ZS-GWBS
CHF 14.90
En stock
+ −
Graphite shock tower für RS1.0 vorne
YOK-RS-017G
CHF 14.90
En stock
+ −
Graphite shock tower für RS1.0 hinten
YOK-RS-018G
CHF 22.90
En stock
+ −
Alu Brush Motor Adapter für RS1.0
YOK-RS-302AD
CHF 8.90
En stock
+ −
RP Ultra Shock Oil #27.5 (Light Yellow)
YOK-RP-113275
CHF 8.90
En stock
+ −
RP Ultra Shock Oil #32.5 (Brown)
YOK-RP-113325
CHF 8.90
En stock
+ −
RP Ultra Shock Oil #37.5 (Purple)
YOK-RP-113375
CHF 8.90
En stock
+ −
RP Ultra Shock Oil #42.5 (Blue)
YOK-RP-113425
CHF 8.90
En stock
+ −
Steel S2 Front Chassis weight for SO2.0
YOK-Z2-002FWS
Steel front chassis weight for SO2.0. Installed under the front side servo of the chassis and adjusted the weight and rigidity. Weight is approximately 20g.
CHF 17.50
En stock
+ −
Alum. S2 Front Chassis weight for SO2.0
YOK-Z2-002FWA
Aluminum front chassis weight for SO2.0. Installed under the front side servo of the chassis and adjusted the weight and rigidity. Weight is about 7g.
CHF 17.50
En stock
+ −
13 Shock Plastic Parts for SO/MO2.0
YOK-S4-S913
CHF 11.90
En stock
+ −
13 Spring Adjust Nut for SO/MO2.0
YOK-S4-S4AJ13
CHF 7.50
En stock
+ −
O-Ring Set (2set) for SO/MO2.0 (Light Weight)
YOK-S4-S3OS
CHF 3.90
En stock
+ −
13Shock Piston f1.6x2x2.0mmfor SO/MO2.0
YOK-S4-S16213
Piston for F13mm shock. The hole diameter is 1.6mm and there are 2 holes. The thickness of the piston is 2.0mm. Contains 2 pieces.
CHF 7.90
En stock
+ −
13Shock Piston f1.7x2x2.0mmfor SO/MO2.0
YOK-S4-S17213
Piston for F13mm shock. The hole diameter is 1.7mm with 2 holes. The thickness of the piston is 2.0mm. Contains 2 pieces.
CHF 7.90
En stock
+ −
13Shock Piston f1.8x2x2.0mmfor SO/MO2.0
YOK-S4-S18213
Piston for F13mm shock. The hole diameter is 1.8mm and there are 2 holes. The thickness of the piston is 2.0mm. Contains 2 pieces.
CHF 7.90
En stock
+ −
Graphite RTC Axle Block Spacer (2.4mm)
YOK-B12-RTC-7
This graphite plate is mounted on the front bumper to strengthen the bumper. By catching crashes and other impacts with the bulkhead, it prevents damage to the front part of the main chassis.
CHF 12.90
En stock
+ −
Graphite Bumper Support (2.4mm
YOK-B12-001BS
This graphite plate is mounted on the front bumper to strengthen the bumper. By catching crashes and other impacts with the bulkhead, it prevents damage to the front part of the main chassis.
CHF 9.90
En stock
+ −
Graphite Front Shock Tower Stiffner (2.4mm)
YOK-B12-017S
This graphite plate connects the lower portion of the front shock tower to increase rigidity. It increases the rigidity of the shock tower and improves the shock's operating precision, while leaving the bulkhead surrounding it supple.
CHF 9.90
En stock
+ −
Graphite Separate Battery Holder
YOK-B12-118S
Lightweight graphite battery holder. Split front and rear sections allow the chassis to remain flexible for torsion. Spacers are included to adjust to the battery thickness.
CHF 20.90
En stock
+ −
Graphite Steering Block Arm L (2.4mm)
YOK-B12-RTC-5L
Graphite arm plate with an extended tie rod mounting position compared to the RTC standard arm to reduce toe-in change during suspension stroke. It improves turning performance especially on high grip surfaces.
CHF 11.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT8 (6.25t) 2stk.
YOK-YS-12625F
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT7 (6.50t) 2stk.
YOK-YS-12650F
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT6 (6.75t) 2stk.
YOK-YS12675F
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT5 (7.00t) 2stk.
YOK-YS-12700F
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT4 (7.25t) 2stk.
YOK-YS-12725F
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT6 (10.0t) 2stk.
YOK-YS-12100R
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT5 (10.5t) 2stk.
YOK-YS-12105R
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT4 (11.0t) 2stk.
YOK-YS-12110R
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Yokomo Off-Road 13mm Feder DOT3 (11.5t) 2stk.
YOK-YS-12115R
These springs are compatible with the F13mm high-capacity shocks adopted from the SO2.0 off-road car. The hardness of the spring is laser-engraved according to the number of turns the higher the number of DOT, the harder the spring. There are 5 types of front releases and 4 types of...
CHF 9.90
En stock
+ −
Center Bone 100mm for MO2.0
YOK-MO-010B10
CHF 8.50
En stock
+ −
Center Bone 51mm for MO2.0
YOK-MO-010B51
CHF 8.50
En stock
+ −
Center Bone 67mm for MO2.0
YOK-MO-010B67
CHF 8.50
En stock
+ −
Graphite Front Shock Tower for MO Series
YOK-MO-017
CHF 18.90
En stock
+ −
Graphite Rear Shock Tower for MO Series
YOK-MO-018
CHF 22.90
En stock
+ −
Graphite Battery Plate for MO2.0
YOK-MO-118P
CHF 6.90
En stock
+ −
Graphite Servo Mount Plate for MO2.0
YOK-MO-203P
CHF 9.90
En stock
+ −
Alum.Center Mount for MO2.0
YOK-MO-302CM
CHF 21.50
En stock
+ −
Slipper Nuts/Spring for MO2.0
YOK-MO-303AJ
CHF 8.90
En stock
+ −
Center Diff. Bearing Collar for MO2.0
YOK-MO-303BC
CHF 4.90
En stock
+ −
COL Drive Cup for MO2.0
YOK-MO-303DCB
CHF 21.90
En stock
+ −
Front Drive Plate for MO2.0
YOK-MO-303DP
CHF 7.90
En stock
+ −
Main Drive Shaft for MO2.0
YOK-MO-303MS
CHF 8.90
En stock
+ −
Slipper Outer Plate for MO2.0
YOK-MO-303OP
CHF 8.90
En stock
+ −
Graphite Center Mount Plate for MO2.0
YOK-MO-304CP
CHF 10.90
En stock
+ −
Graph.Steering Block Plate DOT1 for MO Series
YOK-MO-415P1
CHF 11.90
En stock
+ −
COL Adjusting Screw Set for MO2.0
YOK-MO-303AJS
CHF 4.90
En stock
+ −
f12xf18x4mm Ball Bearing (2 pcs.)
YOK-BB-1812-2
CHF 9.90
En stock
+ −
Battery Stopper
YOK-RS-118
CHF 4.90
En stock
+ −
FRP F/R Upper Deck (2.0mm)
YOK-RS-003
CHF 12.50
En stock
+ −
FRP Center Upper Deck (2.0mm)
YOK-RS-003B
CHF 5.90
En stock
+ −
Verfügbarkeit
Verfügbar beim Lieferanten
Abmessungen
Auswahlhilfe
Material
Prix
CHF
–
CHF
  • CHF 1.5
  • CHF 849
Reifen/Rad-Typ
Servo-Typ
Verwendung
Massstab
Motor / Antrieb
Einsatz
Anspruch
Lackierung
Fertigungsgrad
Max. Geschwindigkeit
Marke
Betriebsspannung